|
Các loại máy hiện sóng tương tự (analog oscilloscope) của Pintek (Taiwan). Hiện nay được sử dụng rất nhiều tại các trường cao đẳng, đại học.
Vui lòng tham khảo thông số kỹ thuật và bảng giá sản phẩm
PS-1000 : Analog oscilloscope (máy hiện sóng, dao động ký) 100Mhz của intek
Cung cấp đầy đủ CO , CQ
Vui lòng tham khảo bảng giá Pintek
- 100MHz BANDWIDTH.
- 20MHz LIMIT.
- 1mV SENSITIVITY.
- 2.0nS RESOLUTION.
- CE. TUV GS, UL, CUL, IEC1010
PS-1000
| Type : |
Rectangular with integral graticule. |
| Display Area : |
8 x 10 div ( 1 div = 1 cm ) |
| Accelerating Voltage : |
14 kV. |
| Phosphor : |
P31. |
|
VERTICAL AMPLIFIERS ( CH 1 and CH 2 )
|
| Sensitivity : |
5 mV / div to 5 V / div ( X1 mode ).
1 mV / div to 1 V / div ( X5 mode ).
1-2-5 sequence, 10 step attenuator.
Vernier control provides fully adjustable
attenuation between steps.
|
| Accuracy : |
± 3 % ( X1 mode ).
± 5 % ( X5 mode ). |
| Input Resistance: |
1 MΩ ± 2 % |
| Input Capacitance: |
25 pF ± 10 pF. |
|
Frequency Response:
|
| 5 mV to 5 V / div ( CAL ): |
DC to 25 MHz (-3 dB). |
| 1 mV / div (CAL): |
5mV/div~5V/div: DC~50MHz(-3db) |
| Rise Time: |
Approximately 3.5 ns. |
| Operaing Modes: |
| CH1: |
CH 1, single trace. |
| CH2: |
CH 2, single trace. |
| ALT: |
Dual trace, alternating. |
| CHOP: |
dual trace, chopped. |
| ADD: |
algebraic sum of CH 1 + CH 2. |
| Polarity Reversal (Invert): |
CH 2 only. |
| Maximum Input Voltae: |
400 V dc + ac peak. |
|
Maximum Undistorted Amplitude:
|
| DC-to-120 MHz: |
4 divisions. |
| DC-to-60 MHz: |
8 divisions. |
|
HORIZONTAL AMPLIFIER ( Input through channel 1 input )
|
| X-Y mode: |
switch selectable using X-Y switch. |
| CH 1: |
X axis. |
| CH 2: |
Y axis. |
| Sensitivity: |
1mV/DIV - 5V/DIV |
|
Accuracy:
|
| Y-Axis: |
± 3%. |
| X-Axis: |
± 6%. |
| Input Impedance: |
1MΩ //25PF
|
| Frequency Response: |
DC to 1 MHz typical ( -3 dB ). |
| X-Y Phase Difference: |
Approximately 3° at 50 kHz. |
| Maximum Input Voltage: |
400V dc+ac pack |
|
SWEEP SYSTEM
|
| Sweep Speed: |
20 ns/div to 0.5 s/div in 1-2-5 sequence, 23
steps.Vernier control porvides fully adjustable
sweep time between steps. |
| Accuracy: |
± 3 %. |
| Sweep Magnification: |
10X, ± 10% extend sweep
speed up tp 2 ns/div. |
| Holdoff: |
Continuously adjustable from NORM to 5 times normal. |
|
TRIGGERING
|
| Trigger Modes: |
AUTO ( free run ) or NORM. |
| Trigger Source: |
CH1, CH2, ALT, EXT, LINE. |
|
Maximum External Trigger Voltage:
|
300 V dc + ac peak. |
|
Trigger Coupling:
|
| AUTO ( AC ): |
30 Hz to 120 MHz. |
| TV-H ( AC ): |
Used for triggering from horizontal sync pulses. |
| TV-V ( DC ): |
Used for triggering from vertical sync pulses. |
| Trigger Sensitivity: |
| Internal: |
1.0 division. |
| External: |
200 mV. |
|
OTHER SPECIFICATIONS
|
| Calibrating Voltage: |
1 kHz ( nominal ) Positive Square Wave, 0.5 V p-p ( ± 3% ) |
| Trace Rotage: |
Electrical, front panel adjustable. |
| Power Requirements: |
115/230 VAC ± 10%, 50/60Hz,?
approximately 60 W. |
| Dimensions: |
324 x 132 x 398 mm ( 12.8 x 5.2 x 15.6" ). |
| Weight: |
Approximately 8.5 kg ( 18.7 1bs ). |
| C E STANDARD: |
E.M.C. Regulations-1992 )E.C. Directive
89/336/EEC)EN 50081-1 Emissions.
EN 50082-1 Immunity. |
|
Pintek (Đo kiểm) 
