|
Các loại máy hiện sóng tương tự (analog oscilloscope) của Pintek (Taiwan). Hiện nay được sử dụng rất nhiều tại các trường cao đẳng, đại học.
PS350 : Analog Oscilloscope (máy hiện sóng, dao động ký) 40Mhz của Pintek
Cung cấp đầy đủ CO , CQ
Vui lòng tham khảo bảng giá Pintek
MAIN FEATURES
- - 40MHz DUAL TRACE, DUAL TRIGGER.
- - VERT SENSITIVITY FROM 1mV/DIV TO 15V/DIV.
- - SWEEP RATE FROM 10nS/DIV TO 2S/DIV.
- - HOLD-OFF, X-Y OPERATION.
- - CE, TUV GS, UL, CUL, IEC1010.
MORE INFOMATION
|
CRT Type:
Display Area :
Accelerating Voltage :
Phosphor :
|
Rectangular with integral graticule.
8 x 10 div ( 1 div = 1 cm)
2.1 kV
P31.
|
|
VERTICAL AMPLIFIERS ( CH 1 and CH 2 )
|
|
Accuracy :
|
± 3 % ( X1 mode ). ± 5 % ( X5 mode ).
|
|
Sensitivity :
|
5 mV / div to 5 V / div ( X1 mode ).
1 mV / div to 1 V / div ( X5 mode ).
1-2-5 sequence, 10 step attenuator.
Vernier control provides fully adjustable
attenuation between steps.
|
|
Input Resistance:
Input Capacitance:
|
1 MΩ ± 2 %
25 pF ± 10 pF.
|
|
Frequency Response:
|
5 mV to 5 V / div ( CAL ):DC to 40 MHz (-3 dB). 1 mV / div : DC to 15 MHz (-3 dB).
|
|
Rise Time:
|
Less then 8.8 nS
|
|
Operaing Modes:
|
CH1: CH 1, single trace. CH2: CH 2, single trace. ALT: dual trace, alternating. CHOP: dual trace, chopped. ADD: algebraic sum of CH 1 + CH 2.
|
|
Polarity Reversal (Invert):
|
CH 2 only.
|
|
Maximum Input Voltae:
|
400 V dc + ac peak.
|
|
HORIZONTAL AMPLIFIER
|
( Input through channel 1 input )
|
|
Sensitivity:
|
1mv/div to 5v/div
|
|
Accuuacy:
|
Y-Axis: ±3%. X-Axis: ± 6%.
|
|
Input Impedance:
|
1MΩ //25PF
|
|
Frequency Response:
|
DC to 1 MHz typical ( -3 dB ).
|
|
Maximum Input Voltage:
|
400V dc+ac pack
|
|
X-Y Phase Difference:
|
Approximately ±3° at 50 kHz.
|
|
SWEEP SYSTEM
|
|
Sweep Speed:
|
0.1 μs/div to 2S/div in 1-2-5 sequence, 23 steps. Vernier control porvides fully adjustable sweep time between steps.
|
|
Accuracy:
|
+ / -3 %.
|
|
Sweep Magnification:
|
10X, ±10%( 2S/DIV - 0.2 μS/DIV). extend sweep speed up to 10nS/DIV.
|
|
Sweep Display Mode:
|
Main, Mix, Delay.
|
|
Hold Off Time:
|
Continuously adjustable from NORM to 5 times normal
|
|
TRIGGERING
|
|
Trigger Coupling:
|
AUTO ( free run ) or NORM
|
|
Trigger Source:
|
CH1, CH2, ALT, EXT, LINE
|
|
Maximum External Trigger Voltage:
|
300 V dc + ac peak.
|
|
Trigger Coupling:
|
AC : 30 Hz to 40 MHz. TV - H (AC): Used for triggering from horizontal sync pulses. TV - V : (DC) Used for triggering from vertical sync pulses.
|
|
Trigger Sensitivity:
|
Internal: 0.5 division ( 1 division with TV Coupling ). External: 500 mV.
|
|
OTHER SPECIFICATIONS
|
|
Calibrating Voltage:
|
1 kHz ( nominal ) Positive Square Wave, 2.0 V p-p ( ± 3% )
|
|
Trace Rotage:
|
Electrical, front panel adjustable.
|
|
Power Requirements:
|
Max. 6 Vrms ( open circuit ).
|
|
Dimensions:
|
324 x 132 x 398 mm ( 12.8 x 5.2 x 15.6" ).
|
|
Weight:
|
Approximately 7.8 kg ( 17.2 1bs ).
|
|
Rated Range of Use
|
10°C-35°C, 10-80% R.H.
|
|
Limits of Operation:
|
0°C-50°C, 10-80% R.H
|
|
Storage Environment
|
-30°C-70°C, 10-90% R.H.
|
|
Pintek (Đo kiểm) 
